Skip to content
Help Center

Set the Meta campaign and ad set in the Deployment Wizard ​

Step 3 of the Deployment Wizard for Meta is Destination, titled Campaign and ad set. You reach it from Ads. See Deployment Wizard for steps 1 and 2 and Review and publish Meta ads with the Deployment Wizard for steps 4 and 5.

Problem and intended user ​

A media buyer (the person who runs your paid ads) needs the new ads in the right Meta campaign and ad set. A mistake here sends ads to the wrong place or leaves them blocked.

Current workflow ​

The media buyer builds the campaign and the ad set by hand in Meta Ads Manager, then uploads each ad into them.

Prerequisites ​

  • Steps 1 and 2 done for Meta. See Deployment Wizard.
  • Meta Ads connected, to pick Meta. Until it is connected, the Meta card on Ads is switched off and says "Meta isn't connected." Select Go to Integrations to fix it. See Meta Ads.
  • A Facebook Page and an Instagram account picked for your Meta ads. Destination asks for each one and links to Integrations.
  • Your Commander Meta ad budget, to create a new campaign. Without it, Destination shows "Set up your Commander Meta ad budget before deploying ads."

How Commander works ​

Fixed rules, not AI, decide which campaigns and ad sets can take your ads. Nothing goes to Meta as an ad until you press Publish in step 4. Before that, Continue on a new campaign or ad set creates it on Meta, paused.

Choose the campaign and ad set ​

With Meta picked, the Destination step is titled Campaign and ad set. For Google, see Set the Google campaign and ad group in the Deployment Wizard. Under Start from, Recommended by Commander builds a new campaign and ad set, and Last used or Saved setup reuses an earlier one. Neither offers a setup whose campaign or ad set was deleted or archived on Meta. Every value stays editable. If you change a reused setup's campaign (new or existing, or another campaign) or its ad set, neither card stays selected, because what you have is no longer that setup. Select the card again to bring its values back.

  • Campaign: pick New campaign or Add to an existing campaign. A new campaign has an Objective (Awareness, Consideration, Conversion or Retention) and a Strategy (Optimize or Experiment), and is created paused. Under an active existing campaign you picked, a line says where the new ads spend from once you switch them on: "Active. Once you switch the new ads on, they spend from its … budget.", or "…from the ad set's budget." when the campaign's budget sits on its ad sets.
  • Ad set: pick Create a new ad set or Add to an existing ad set. A new ad set has an audience, locations, placements, a schedule, age and gender. Under Placements, a line counts the placements a Single image or carousel cannot reach. With Single image, Switch ad format in step 2 goes back to the Ads step. Under a ticked Feed in the Facebook or Instagram group, an ad with only a 9:16 picture shows "Cropped from your 9:16 picture." with buttons to add a shape that fills the feed: Add 4:5, Add 1:1 and Add 1.91:1 for Facebook, Add 4:5 and Add 1:1 for Instagram. Facebook Feed takes a 4:5, a square or a 1.91:1 picture.
  • Daily budget: a new campaign holds its budget on the campaign or on the ad set (Campaign budget or Ad set budget). Commander ad budget remaining shows what is left.
  • Account and identity: shows the Facebook Page, the ad account, the Instagram account and the pixel.

The list shows only the campaigns that can take these ads. Refresh from Meta reads your campaigns again.

An ad set holds at most 50 ads that are not archived or deleted. Paused, in review and rejected ads count, because this is Meta's limit. Before it refuses an ad set as full, the wizard re-counts the ads on Meta ("Checking the ad set's room on Meta…"). Close to the limit, the step says how many ads the ad set will hold.

WARNING

Continue on a new campaign or ad set creates it on Meta, paused. A failed publish later does not remove it.

Next, Review and publish Meta ads with the Deployment Wizard covers step 4.

Exact output ​

Continue creates a new campaign or ad set on Meta, paused, and leaves an existing one as it is. No ad exists on Meta yet. The Campaign and ad set step shows these parts:

  • Start from: the cards Recommended by Commander, Last used and Saved setup.
  • Campaign: New campaign or Add to an existing campaign, with its Objective and Strategy when new.
  • Ad set: Create a new ad set or Add to an existing ad set.
  • Daily budget: with Commander ad budget remaining.
  • Account and identity: the Facebook Page, the ad account, the Instagram account and the pixel.

What to do with it ​

What you seeActionOwner
Start from offers Last used or Saved setupSelect a card to reuse an earlier campaign and ad set, then edit any value.media buyer
The campaign list does not show a campaign you expectSelect Refresh from Meta to read your campaigns again.media buyer
An ad set close to its limitRead how many ads it will hold. Create a new ad set when it is full.media buyer
A line under Placements counts placements a Single image or carousel cannot reachSelect Switch ad format in step 2 with Single image, and pick another format.media buyer
"Cropped from your 9:16 picture." under a ticked FeedSelect Add 4:5, Add 1:1 or, for Facebook, Add 1.91:1 to add a picture that fills the feed, or leave the ad as it is.media buyer
Continue on a new campaign or ad setGo on to Review and publish Meta ads with the Deployment Wizard. The campaign and ad set stay on Meta, paused, even if a later publish fails.media buyer

Expected value and measurement ​

The wizard replaces building the campaign and ad set by hand. To check the ads once they run, open Performance > Campaigns or Performance > Ad Containers. You cannot isolate the effect of the wizard when other creative, budget or audience changes ran at the same time. See Campaigns and Ad Containers.

Limitations and exceptions ​

When something fails ​

MessageWhat to do
"Couldn't create it on Meta. Try Continue again."Select Continue again on Destination.
"Couldn't load your Meta campaigns. Try again in a moment."Wait a moment and try again. You can also create a new campaign instead.

Demo Mode ​

The page shows a Sample data badge next to the heading. Demo Mode creates nothing on Meta. Continue on Destination only moves on.

Commander is built by Omniconvert.